準備工作 在使用碳氫真空清洗機清洗化學設備之前，需要先做一些準備工作。，檢查清洗機的電源和氣源是否正常，確保設備能夠正常啟動和工作。然后，準備好所需要的清洗介質，一般為氟利昂氣體。同時，清洗前需要對要清洗的化學設備進行檢查，確保設備表面沒有雜質和嚴重的損壞。

Before using a hydrocarbon vacuum cleaner to clean chemical equipment, some preparation work needs to be done. Firstly, check if the power and air supply of the cleaning machine are normal to ensure that the equipment can start and work properly. Then, prepare the required cleaning medium, usually Freon gas. At the same time, it is necessary to inspect the chemical equipment to be cleaned before cleaning to ensure that the surface of the equipment is free of impurities and severe damage.

將化學設備放入清洗機 將要清洗的化學設備放入碳氫真空清洗機的清洗室內，注意將設備放置在固定位置，避免在清洗過程中發生移動和傾斜。同時，要確保設備與清洗機的密封圈緊密貼合，避免在清洗過程中氣體泄漏。

Place the chemical equipment into the cleaning room of the hydrocarbon vacuum cleaning machine. Pay attention to placing the equipment in a fixed position to avoid movement and tilting during the cleaning process. At the same time, it is necessary to ensure that the sealing ring between the equipment and the cleaning machine is tightly fitted to avoid gas leakage during the cleaning process.

調整清洗參數 根據化學設備的特性和清洗要求，調整碳氫真空清洗機的清洗參數。主要包括清洗介質的壓力、時間、溫度和超聲震蕩頻率等。一般來說，清洗壓力和時間根據設備的特性和污漬的程度進行調整，清洗溫度一般設置在常溫或略高于常溫，超聲震蕩頻率根據設備材質和污漬的固化程度進行選擇。

Adjust the cleaning parameters of the hydrocarbon vacuum cleaning machine based on the characteristics and cleaning requirements of the chemical equipment. This mainly includes the pressure, time, temperature, and ultrasonic oscillation frequency of the cleaning medium. Generally speaking, the cleaning pressure and time are adjusted according to the characteristics of the equipment and the degree of stains. The cleaning temperature is generally set at room temperature or slightly higher than room temperature, and the ultrasonic vibration frequency is selected based on the equipment material and the degree of solidification of the stains.

啟動清洗機 調整好清洗參數后，啟動碳氫真空清洗機，開始清洗化學設備。清洗機會自動建立真空環境，并通過氟利昂氣體在設備表面形成薄膜，溶解和清洗污漬。同時，超聲震蕩產生的能量會進一步加速污漬的分解和清洗。

After adjusting the cleaning parameters, start the hydrocarbon vacuum cleaning machine and start cleaning the chemical equipment. The cleaning machine automatically establishes a vacuum environment and forms a thin film on the surface of the equipment through Freon gas to dissolve and clean stains. Meanwhile, the energy generated by ultrasonic vibration will further accelerate the decomposition and cleaning of stains.

結束清洗 根據化學設備的特性和清洗要求，設定清洗時間。在設定的清洗時間到達后，停止清洗機的工作。然后，打開清洗室的門，將清洗完的化學設備取出。

End cleaning: Set the cleaning time based on the characteristics and cleaning requirements of the chemical equipment. Stop the cleaning machine after the set cleaning time is reached. Then, open the door of the cleaning room and take out the cleaned chemical equipment.

檢查和保養 取出清洗完的化學設備后，對設備的清洗效果進行檢查。主要包括檢查設備表面是否干凈，污漬是否完全去除等。如果清洗效果不理想，可以重新進行清洗。在清洗機的使用過程中，還需要定期對清洗機進行維護保養，清洗設備的靈敏度，確保其正常工作。

After inspecting and maintaining the cleaned chemical equipment, check the cleaning effect of the equipment. This mainly includes checking whether the surface of the equipment is clean and whether the stains are completely removed. If the cleaning effect is not ideal, it can be cleaned again. During the use of the cleaning machine, it is also necessary to regularly maintain and maintain the sensitivity of the cleaning equipment to ensure its normal operation.

在使用碳氫真空清洗機清洗化學設備時，需要注意以下幾點：

When using a hydrocarbon vacuum cleaner to clean chemical equipment, the following points should be noted:

防護：在操作過程中，必須嚴格遵守操作規程，戴好防護眼鏡、手套等個人防護用品，避免對皮膚、眼睛等產生傷害。同時，要確保清洗機的電源和氣源正常，避免發生意外事故。

Safety protection: During the operation, it is necessary to strictly follow the safety operating procedures, wear personal protective equipment such as protective glasses and gloves, and avoid injury to the skin, eyes, etc. At the same time, it is necessary to ensure that the power and air sources of the cleaning machine are normal to avoid accidents.

清洗介質選擇：選擇合適的清洗介質，避免對設備表面和環境產生污染和損害。同時，盡量選擇環境友好、無害的清洗介質，減少對人體和環境的危害。

Selection of cleaning medium: Choose a suitable cleaning medium to avoid pollution and damage to the equipment surface and environment. At the same time, try to choose environmentally friendly, non-toxic and harmless cleaning media to reduce the harm to human health and the environment.

清洗參數調整：根據不同的設備特性和污漬程度，調整清洗參數，確保清洗效果。同時，要避免清洗壓力過高和清洗時間過長，以免對設備表面造成損傷。

Cleaning parameter adjustment: Adjust the cleaning parameters according to the characteristics of different equipment and the degree of stains to ensure the cleaning effect. At the same time, it is important to avoid excessive cleaning pressure and prolonged cleaning time to prevent damage to the surface of the equipment.

清洗機維護：定期對清洗機進行維護保養，清洗設備的靈敏度，確保其正常工作。保持清洗室內的潔凈和干燥，避免污染和設備故障。

Cleaning machine maintenance: Regular maintenance and upkeep of the cleaning machine to ensure the sensitivity of the cleaning equipment and its normal operation. Keep the cleaning room clean and dry to avoid contamination and equipment malfunctions.